Flash Deals
F14892 C DIY RC Drone Quadrocopter RTF X4M360L Frame Kit with GPS APM 2 8 AT9
Click to see details
F14892 C DIY RC Drone Quadrocopter RTF X4M360L Frame Kit with GPS APM 2 8 AT9

F14892-C DIY RC Drone Quadrocopter RTF X4M360L Frame Kit with GPS APM 2.8 AT9 TX

100 % of buyers enjoyed this product!
Availability: in stock
TODAY'S DEAL Ends in: 04:36:18
Price:  $ 209.00 / piece
Sale Price:  $ 177.65 / piece
from AliExpress
45 days Money back 45 days Money back Returns accepted if product not as described, buyer pays return shipping; or keep the product & agree refund with seller.
On-time Delivery On-time Delivery
Guarantees: On-time Delivery 60 days

Sort By

Top-rated Seller

Share:

DIY RC Drone Quadrocopter Whole Set X4M360L Frame Kit with GPS APM 2.8 AT9 RX TX Battery Motor ESC RTF Unassembled,buyer need to assemble by themselves.

Package include:

1xX4M360L frame 2x920KV CW Brushless Motor 2x920KV CCW Brushless Motor 4x30A Brushless ESC 2X8443 8.4*4.3″ Carbon Fiber Propeller Self-locking Props 1XMK KK Multi-Copter Power Battery to 8 ESC Connection Board 1XAPM 2.8 Flight control 1x6M GPS with Compass 1x5pcs 10cm Servo Receiver Extension Lead Wire Cable 1xGPS Folding Antenna Mount Holder 12×3.5mm banana plug 1xDeans Style T Plug Male Connector Silicone Wire With 11.5CM 14awg 1xHook and & Loop Fastening Tape 1xRadiolink AT9 9 Channel Transmitter & Receiver
11.1V 3300Mah 25C lipo battery About the APM 2.8 Flight control,here is the user manual

Before you can configure your APM,

you will need to first connect everything together.

This guide will show you all the cables and parts that you will need to connect to your APM.

Typical Quadcopter Layout
Please note the illustration Below highlights a (TYPICAL) installation. It contains optional equipment including a Camera Gimbal and a Battery Monitor and it utilizes an ESC wired “Y” power connection rather than the power distribution board common to many MultiCopters.

1. Connecting your motors and RC gear

Overview of connections on the Ardupilot Mega v2 board Note: the instructions below are for regular RC receivers with PWM output (one cable per channel). If you’re using a “PPM” receiver (one cable carries all channels), follow the instructions .

Before you can configure your Arducopter, you will need to first connect everything together. This is quite easy. You need to connect your RC receiver to the Input side of the board. You can use the cables included with your Arducopter Kit, or if you are using another frame, you can use jumper cables, or female to female servo cables Connections between RC receiver and Ardupilot Mega v2 board

If you are using female to female servo cables, the ground (black) side of each connector must be on the outside for the board, the signal (white/orange) needs to be on the inside as shown below.

Connecting with straight connectors Connecting with right angle connectors

If you are using a multi-pin connector that was included with your Arducopter Kit, connect them as shown below

Input Side for RC reciever Output side to PDB

Please note, that your ESC, connectors should be plugged in the the output side, it is suggested that you only use power from one of your ESC’s. This can be dune by cutting the red wire on all but one of the ESC’s, or by using a special adaptor.

2. Connecting ArduCopter motors

Once again if you are using an Arducopter Kit, with the PDB, then you dont need to worry about this if you soldered everything correctly as the motors are assigned to the correct pins with the cables you plugged connected in the previous step. However you will neet to make sure your motors are spinning in the correct direction. The images below show the possible arducopter configurations with correct motor orientation Quick Tip: If your motor is not spinning in the correct direction, simply switch the position of any two of the ESC-motor wires.

Arducopter Quad

Arducopter Tri

Arducopter Hexa, Octa, and Y6

Arducopter OCTA QUAD (X8)

Connecting a Roll-Tilt Camera mount

3. Connecting Optional Sensors

Sonar – Ultrasonic Rangefinder

AC2 supports the MaxSonar line of sonars for low level altitude hold and in the future collision avoidance. Below 10 meters sonar is primarily used for altitude hold. Above 10 meters, the barometric sensor is used. GPS is not required for altitude hold.


Connect your Ultrasonic Sensor to the A0 port of your Ardupilot Mega v2 board
The sonar sensors are quite sensitive to noise, adding something like a ferrite choke to your cable could help. The most important is to mount your sonar away from other electronics like ESC, or wireless telemetry modules.

Possible Causes of sonar Interferance

  • Electrical noise caused by ESCs, Servos, or switching BEC’s on the same circuit as the Sonar
  • EMF radiation from motors, motor wires, ESC’s or Xbee.
  • Acoustic noise from propellers
  • Vibration from motors, props, etc.

Optical Flow Sensor

The optical flow sensor is used to improve the position hold accuracy of your arducopter. This sensor is supported from Arducopter 2.6 and above.


Connecting the optical flow sensor to APMv2

  • Power, GND, NCS pins should be attached to A3
  • MISO, MOSI and SCLK pins should be directly soldered to the pins shown above
  • Default mounting is lens pointing down, pins forward
Its a good idea to secure the wires with some cable ties so they dont break off over time

How to connect the optical flow sensor to your ardupilot mega board. Make sure the pins are facing forward Now that everything has been connected everything the next thing to do is configure arducopter firmware for your frame.
If you have any questions or comments please add them below

Average Star Rating:
0 out of 5 (0 Ratings)
Name Rating Feedback
Shipping Company Shipping Cost Estimated Delivery Time
DHL 3 - 7 days
UPS Expedited 3 - 7 days
EMS 5 - 14 days
Post Air Mail Free Shipping 15 - 45 days
Return Policy If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.

N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
Seller Service On-time DeliveryIf you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).

Most Popular from Category


Price:  $ 209.00 / piece
Sale Price:  $ 177.65 / piece
from AliExpress